Bathroom Remodel for Small Bathrooms: Plan Storage Before Demo

Author: Oded Feigin · Created On: October 22, 2026 · Last Updated: October 28, 2026

Quick Answer

What storage should you plan before demo in a small bathroom?

Plan everything that lives inside a wall or depends on the plumbing. That covers recessed cabinets and niches, the vanity’s width and drawer layout, blocking for wall loads and the zone above the toilet. A 1979 University of Illinois planning circular found that storage under the bowl of a 24- or 30-inch vanity is nearly useless2. Cabinet width is a layout decision, not a shopping decision.

A bathroom remodel for small bathrooms is the one moment when storage can move into the walls, the vanity drawers and the space above the toilet. Once the tile is set, most of those options close. Bathrooms were the most common remodeling project of 2025, with 73% of remodelers rating them common or very common1. The practical guide to small bathroom storage is the broader overview of the topic. This article covers one decision window: the storage choices to settle before demolition starts.

A small bathroom with recessed shelving built into a wood-paneled wall on either side of a wall-hung toilet and bidet, the kind of storage a bathroom remodel for small bathrooms can build into the walls.
Recessed shelves on both sides of the toilet wall hold everyday items without adding a single inch of floor depth.

Key Takeaways

  • The University of Illinois Small Homes Council found that fixing planning mistakes after the plumbing goes in is costly and often structurally impractical2. Storage is cheapest to decide while the studs are bare.
  • HUD Minimum Property Standards, as cited by the Small Homes Council in 1979, called for grab bars and their supports to hold 250 pounds2. Blocking added during demo is a small framing task compared with opening a finished wall.
  • Not every wall can take recessed storage. The plumbing wall, an outside wall and the wall that houses a pocket door are usually already spoken for.
  • The common mistake is to choose storage before the clearances. Fix the toilet, door and shower space first, then give storage what remains.

Before Demo: What to Have Ready for a Bathroom Remodel for Small Bathrooms

A small bathroom remodel is cheapest to change while the plan is still on paper, before the first tile comes off. Demolition is the stage where old finishes and fixtures come out and the wall framing is exposed. That exposure is short, and storage ideas that need framing expire when the drywall goes back up. Have these ready before it starts:

  • A measured floor plan with the door swing, the window and every fixture drawn to scale.
  • A storage inventory sorted by how often each item is used.
  • Chosen fixtures, because the Small Homes Council advised that fixture sizes must be known at the start of planning2.
  • The team: a licensed contractor for framing, a licensed plumber for anything that moves a pipe, and a licensed electrician for lighted or powered cabinets.
  • Permission: permits from the local building department, and written approval from the landlord or condo association where one applies.

Renters rarely control a remodel, but the same list still helps. If the landlord is planning one, ask for a drawer vanity and a recessed cabinet while the walls are open. Freestanding and tension-mounted storage can follow after move-in, with no drilling at all.

The plan exists to protect one short window, the days when the studs are bare. That is the only time storage can be built into the room rather than added to it.

Step 1: Inventory What the Bathroom Has to Store

By the end of this step, you’ll have a list of what the room must hold, sorted into daily, weekly and backstock items. Storage where behavior happens starts with knowing the behavior. Daily items such as toothbrushes, skin care and a hair dryer belong within reach of the sink. Weekly items such as cleaning supplies can sit lower or higher. Backstock, the spare paper and refills, can live farthest away.

Linens are the bulky category, and they are easy to underestimate. The Small Homes Council sized a family of four’s bathroom linens at six bath towels, six face towels, four guest towels, six washcloths and a bath mat3. Its recommended space also covers paper products, lotions, soap, cleaning supplies and water bottles3. One alternate layout for all of it is a shelf unit 30 inches wide and 12 inches deep3.

  1. Empty the current bathroom onto a table and group every item by how often it gets used.
  2. Count the linens that must stay in the room and the ones a hall closet can hold.
  3. Flag the items that must stay dry, such as spare paper and first-aid supplies.
  4. Mark the items that need an outlet, such as a hair dryer or an electric toothbrush.

Check the result with one question: does every daily item have a place within an arm’s reach of the sink? Where the answer is no, that gap becomes the brief for the vanity and the recessed cabinet.

An inventory turns a vague wish for more storage into a measured brief, which lets the remodel size cabinets to the routine instead of to a catalog page.

Step 2: Lock the Fixture Clearances Before Placing Storage

By the end of this step, you’ll know which floor and wall areas belong to the fixtures and can never hold storage. One California city’s remodel handout, citing the state plumbing code, requires a toilet space 30 inches wide and 24 inches clear in front4. That width means 15 inches from the centerline to each side. Other jurisdictions use different figures, so confirm them with the local building department.

Clear floor space is the open area a person needs in front of or beside a fixture to use it, clean it and repair it. The Small Homes Council framed it the same way, asking for room to use each fixture, assist another person, repair it and clean it2. Storage that eats into that space makes the room harder to use every single day.

For accessible toilet rooms, the Access Board sets the toilet centerline 16 to 18 inches from the side wall5. The clear area around it is at least 60 inches wide and 56 inches deep5. Those figures describe accessible design rather than a rule for every home. They are a useful benchmark for anyone planning to age in place.

The door is the clearance people forget. The Council advised choosing or placing the vanity so an opened drawer cannot block the door swing, which could stop someone entering in an emergency2. It also preferred a 32-inch door over the 24-inch width then accepted as the minimum2.

  1. Draw each fixture at its real size on the floor plan.
  2. Shade its clearance zone and the full arc of the door swing.
  3. Mark the wall lengths that remain. Only those can carry storage.

Square footage is fixed, flow is a choice, and a clearance drawn first is what stops a vanity drawer from quietly claiming the doorway.

Step 3: Size the Vanity for Capacity, Not Footprint

By the end of this step, you’ll have a vanity width and drawer layout that hold the daily items from your inventory. Width matters more than most buyers expect. The Small Homes Council found storage below the bowl of a 24- or 30-inch vanity so restricted by the bowl and drain that it is nearly useless2. It called a vanity 36 to 48 inches long desirable for better storage and more counter space2.

The reason is the drain. A sink trap drops into the center of a narrow cabinet and splits the interior into two thin columns. A wider vanity leaves room for drawers beside the plumbing, and drawers keep small items visible instead of stacked behind a door. The Council judged the drawers under the vanity counter in its desirable bathroom plans more than adequate for a family of four’s bath linens2.

An open white vanity drawer organized with nail polishes, perfumes, makeup sponges and three gold-toned hairbrushes in divided compartments.
A shallow vanity drawer with dividers keeps small daily items visible and separated, which a door cabinet beside a drain pipe cannot do.
  1. Measure the wall length left over after the clearances.
  2. Choose the widest vanity that fits without entering the toilet or door zone.
  3. Ask the plumber where the drain and supply lines will land, so the drawers can be planned around them.
  4. Use drawers for daily items, and keep door cabinets for tall bottles and cleaning supplies.

Where the room cannot take a wider cabinet, a shallower one can still win back walking space. The guide to space-saving cabinet types compares narrow floor cabinets, wall-mounted units and over-sink cabinets by footprint and access. A wall-hung vanity also needs solid backing in the wall behind it.

A vanity is judged by the drawer space left after the plumbing, not by its outside size. That is why its width belongs in the floor plan before the plumber roughs in the drain.

Step 4: Claim Recessed Storage While the Walls Are Open

Recessed storage planning starts by finding which wall bays can take a recessed medicine cabinet or a niche. Recessed storage is a cabinet, shelf or niche set into the wall cavity between studs, so it adds capacity without projecting into the room. In a narrow bathroom, that zero projection is the whole point.

Not every wall qualifies. A wet wall is the wall that carries the room’s supply pipes, drains and vent. The Small Homes Council recommended placing fixtures so all piping runs in one wall with a single vent stack, to simplify the plumbing and cut cost2. That wall is already full. The Council also wanted pipes in a warm wall, noting that an insulated 2 x 4 outside wall is not adequate2. A cabinet cut into an outside wall would also displace insulation.

The third wall to check holds the door. A pocket door needs an empty space in the stud wall as wide as the door itself2, so it competes directly with a recessed cabinet. Decide which one gets that wall before framing starts, because both cannot have it.

“After the bathroom is built and the plumbing and equipment installed, the correction of planning mistakes or omissions becomes costly, and is often structurally impractical.”

William H. Kapple, AIA, University of Illinois Small Homes Council-Building Research Council, Bathroom Planning Standards2

Height matters as much as location. For accessible design, the Access Board places the bottom edge of a mirror over a lavatory no higher than 40 inches above the floor5. A recessed mirrored cabinet hung at that height serves seated and standing users alike. A cabinet with lighting or an outlet inside belongs with a licensed electrician, and one city’s handout requires every bathroom receptacle to be GFCI protected4.

Shower niches follow the same logic inside the wet zone. They sit within the waterproofed wall, so the niche’s location, slope and membrane belong in the tile contractor’s plan rather than in a late change order. Standard cabinets are made to fit between two studs; anything wider means cutting a stud and adding a header, which is framing work for the contractor.

Recessed storage is the only bathroom storage that costs no floor depth, so the wall audit decides more capacity than any product chosen afterward.

Step 5: Add Blocking for Every Wall-Mounted Load

After this step, every future grab bar, wall cabinet and heavy shelf will have solid wood behind it. Blocking is solid lumber or plywood fastened between studs so screws have something strong to bite into. Drywall on its own holds very little weight.

The Small Homes Council cited HUD Minimum Property Standards in requiring grab bars and their supports to hold 250 pounds2. That needs firm backing, such as 2 x 4 blocking nailed between studs or half-inch exterior-glue plywood anchored to them2. The Council warned that towel bars will not carry that load and should stay out of the tub and shower area2.

Accessible design treats blocking as a planning item, too. Under the ADA Standards, covered residential dwelling units need not install grab bars if reinforcement is already in the walls where the bars would go5. For accessible toilet rooms, those bars sit 33 to 36 inches above the floor5. That band is worth blocking even in a home that needs no bars today.

  1. Mark every wall-hung item on the wall drawings: vanity, cabinets, shelves, grab bars, towel bars and hooks.
  2. Ask the contractor to add continuous blocking at those heights before insulation and drywall.
  3. Photograph each open wall with a tape measure in the frame, so the blocking can be found later.

Blocking is the cheapest insurance in the whole remodel: one afternoon of framing keeps every future shelf, cabinet and grab bar from depending on drywall anchors.

Step 6: Plan the Wall Above the Toilet

By the end of this step, the wall above the toilet will have a planned depth, height and purpose. The Small Homes Council noted that a storage unit 12 inches deep above the flush tank can hold linens and supplies2. It added that 12 inches of open space are needed above the tank lid so the tank mechanism can be serviced2.

Those two figures line up with the linen inventory. The Council’s alternate layout for a family’s bathroom linens is 30 inches wide and 12 inches deep3. The California toilet space from the clearance step is also 30 inches wide4, although local clearances differ. Where the bay is that wide, a cabinet over the tank can match the footprint of the Council’s linen layout, provided its height leaves the service space clear.

How deep each storage piece needs to be Depth in inches measured from the wall. Over-tank storage unit 12 and vanity counter front to back 21, from University of Illinois Circular C5.7 (1979). Bathroom linen shelf alternate 12 deep and maximum linen shelf or drawer depth 24, from Circular C5.12 (1975). How deep each storage piece needs to be Over-tank cabinet 12 in Bath linen shelf 12 in Vanity counter, front to back 21 in Linen shelf, max depth 24 in 0 12 24 Recommended storage depth Maximum shelf depth Source: Small Space Logic analysis, 2026
An over-tank cabinet and a full bathroom linen shelf share the same 12-inch depth, half the Council’s 24-inch shelf limit, so one shallow cabinet above the toilet can do both jobs. Compiled by Small Space Logic from the Small Homes Council’s bathroom planning circular and its indoor storage circular.

Choose the storage type by the access it gives. Open shelves keep towels visible, while closed cabinets keep backstock dry and free of dust. The comparison of over-toilet shelves and cabinets weighs wall shelves, freestanding étagères and enclosed cabinets on sizing, stability and tank clearance. A freestanding unit needs no drilling, which suits renters, but its legs stand inside the toilet’s clear space.

The wall above the toilet is one of the largest dead zones in a small bathroom, and dead zones are expensive zones. Planned with blocking behind it, that wall becomes the linen closet the room never had.

Step 7: Keep Storage Out of the Moisture Path

Moisture planning puts storage where steam and spray do the least damage. The EPA advises keeping indoor humidity below 60 percent, ideally between 30 and 50 percent6. It also advises running the bathroom fan or opening a window when showering6. One California city requires a bathroom exhaust fan of at least 50 CFM even when the room has an operable window4.

The fan protects the storage, but placement does more of the work. Keep open shelves and linen storage away from the shower opening and from the wall that takes spray. The same handout requires a nonabsorbent wall finish to at least 6 feet above the floor around showers and tubs with shower heads4. Storage inside that zone should be built from tile, stone or other moisture-proof materials.

The shower’s own footprint also limits where a niche can go. The handout requires a shower stall of at least 1,024 square inches that can contain a 30-inch circle4. A recessed niche keeps that minimum stall area clear, so confirm any projecting shelf with the local inspector. The zone-by-zone storage plan sorts which items belong near the shower and which belong well away from it.

Moisture decides the material and placement decides the moisture, so the fan, the niche and the dry linen zone have to be planned together as one system.

Small Bathroom Remodel Storage Decisions and Their Deadlines

Each storage decision in a small bathroom remodel has a deadline set by the construction sequence, not by the calendar. The table lists the decision, the stage that closes it, the figure that governs it and the trade that signs off.

Storage decisionMust be settled beforeGoverning figureWho signs off
Vanity width and drawer layoutRough plumbing36 to 48 in long desirable2Licensed plumber
Recessed cabinet locationFraming inspectionMirror bottom edge 40 in max, accessible design5Contractor
Shower nicheWaterproofingStall area the niche must not reduce: 1,024 sq in (one CA city)4Tile contractor
Blocking for bars and cabinetsInsulation and drywallGrab bars hold 250 lb (HUD standard cited in 1979)2Contractor
Over-toilet cabinetDrywall12 in deep, 12 in clear above tank2Contractor
Lighted or powered cabinetRough electricalGFCI-protected receptacles (one CA city)4Licensed electrician

Most of these deadlines fall early in the job, before the walls close. The storage plan has to be finished before the crew arrives, not worked out as the walls open.

Common Mistakes in Small Bathroom Renovations

The costliest mistakes in small bathroom renovations come from deciding storage in the wrong order. Each one below is cheap to prevent on paper and expensive to undo in tile.

Buying the Vanity Before Drawing the Clearances

A vanity picked from a showroom often turns out too wide for the toilet space or too deep for the door swing. The fix is to draw the clearances first and buy the widest cabinet that still fits between them.

Recessing a Cabinet Into the Wrong Wall

A recessed cabinet planned for the plumbing wall or an outside wall usually meets a vent pipe or insulation once the drywall is off. Run the wall audit before ordering the cabinet, and keep a surface-mounted model as the fallback.

Skipping Blocking Because Nobody Needs Grab Bars Yet

Needs change, and so do owners. Blocking costs a few pieces of lumber while the wall is open, and it later carries shelves, cabinets and a heavy mirror as well as grab bars.

Putting Linen Shelves Beside the Shower

Open towel shelves next to the shower opening take on steam every day. Move dry storage to the far wall or above the toilet, and keep only sealed or waterproof storage inside the spray zone.

What a Successful Small Bathroom Redo Looks Like

A successful small bathroom redo shows up in the daily routine rather than in photos. Every daily item has a home within reach of the sink. The door swings fully open with every drawer pulled out. Towels live in one dry place, and the floor stays clear around the toilet.

  • The vanity drawers hold the daily kit, and the cabinet doors hold tall bottles and cleaning supplies.
  • The recessed cabinet sits on an interior wall, at a height the whole household can use.
  • Blocking photos are saved, so any future grab bar or shelf can go straight into solid wood.
  • The over-toilet storage leaves open space above the tank for repairs.

The last test is the reset. If the room can go from used to tidy in a couple of minutes, the storage is working. The layout guide for storage and flow covers how placement keeps that reset quick. Design for the reset, and the vanity’s drawers do most of the work every morning.

Frequently Asked Questions

What storage should I plan when remodeling a very small bathroom?

Plan the storage that depends on walls and plumbing. That means a recessed cabinet on an interior wall, the widest drawer vanity the clearances allow, blocking behind wall loads and a cabinet above the toilet. The Small Homes Council called a vanity 36 to 48 inches long desirable for storage2.

Is a 24-inch vanity big enough for a small bathroom?

It fits, but it stores little. The Small Homes Council found storage under the bowl of a 24- or 30-inch vanity nearly useless, because the bowl and drain take the space2. Where the wall allows, a wider drawer vanity holds far more. Where it does not, add a recessed cabinet instead.

How deep should storage above the toilet be?

About 12 inches. The Small Homes Council described a unit 12 inches deep above the flush tank for linens and supplies2. It also called for 12 inches of open space above the tank lid for servicing2. Deeper cabinets crowd the user’s head and make the tank harder to reach for repairs.

Can a recessed medicine cabinet go in any bathroom wall?

No. The plumbing wall carries the pipes and vent, which the Small Homes Council recommended grouping in one wall2. An outside wall holds insulation, and a pocket door needs its own empty stud space. An interior partition wall is usually the best candidate, confirmed by a contractor once it is open.

Should I add blocking if nobody needs grab bars yet?

Yes. HUD standards cited by the Small Homes Council in 1979 called for grab bars and supports to hold 250 pounds, which takes solid backing2. Under the ADA Standards, covered residential units may skip installed bars when wall reinforcement is in place5, a useful benchmark for any home. The same blocking later carries shelves and wall cabinets.

Limitations and Edge Cases

  • Clearance and fan figures vary by jurisdiction. The front clearance and exhaust figures here come from one California city’s handout, so check the local building department before framing.
  • The Small Homes Council circulars date from the 1970s. Fixture sizes have changed since then, so check every product against the maker’s listed dimensions, although the planning logic about drains, blocking and door swings still holds.
  • Access Board figures describe accessible design. They serve here as benchmarks, not as requirements for a private home.
  • This plan assumes an owner-controlled remodel. In a rental, the landlord decides, so the planning list works best as a written request.

Conclusion

A bathroom remodel for small bathrooms gains the most storage before demo, not after it. Fix the clearances and size the vanity to its drawers. Then audit the walls for recessed space, block for every wall load and plan the zone above the toilet while the studs are bare. Engineer the layout first, decorate second.

For how these decisions fit the wider topic, see the small bathroom storage overview and its zone-by-zone approach to compact bathrooms.

References

Methodology: every sourced figure in this article comes from an independent published source listed below, each checked against its cited sentence on October 22, 2026, and the planning sequence is a synthesis of those sources by Small Space Logic’s founder, a mechanical engineer.

  1. National Association of Home Builders – Bathroom Remodeling Is Most Common Project in 2025, Eye on Housing, January 30, 2026, from the NAHB/Westlake Royal Remodeling Market Index survey.
  2. University of Illinois Small Homes Council-Building Research Council – Bathroom Planning Standards, Council Notes Circular C5.7, William H. Kapple, Fall 1979.
  3. University of Illinois Small Homes Council-Building Research Council – Indoor Storage, Council Notes Circular C5.12, William H. Kapple, 1975.
  4. City of Pleasanton Building and Safety Division – Residential Bathroom Alteration Requirements, based on the 2022 California codes, revised January 2023.
  5. U.S. Access Board – Guide to the ADA Standards, Chapter 6: Plumbing Elements and Facilities, sections 603.3, 604.2, 604.3.1, 604.5 and 609.4, 2010 ADA Standards for Accessible Design.
  6. U.S. Environmental Protection Agency – A Brief Guide to Mold, Moisture, and Your Home.
Oded Feigin, founder of Small Space Logic
Oded Feigin Founder & Lead Author
Oded Feigin is the Founder of Small Space Logic, a compact home planning brand built around technical-lite spatial systems, layout logic, organization, and engineering-informed design.